Scion IA Forum - Reply to Topic
Thread: Oil change DIY Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Scion IA Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
08-23-2019 01:12 AM
yrwei52
Oil change DIY

Quote:
Originally Posted by WilsonT123 View Post
Anyone have issues with oil drain plug leaking..

Replaced oil drain plug washer with

OEM Oil Drain Plug Washer Gaskets For Mazda Part# 9956-41-400 (amazon)
(seems identical as OEM)
Yes, I have. The first oil change was done by Toyota dealer covered by Toyota's 2-year maintenance program. 2.5 quarts of oil leaked out during the road trip from San Jose to LA! Brought back to the Toyota dealer afterwards the dealer claimed the drain plug aluminum washer is "cracked" and the oil is leaking out from there!
06-20-2019 07:49 PM
WilsonT123 Anyone have issues with oil drain plug leaking..

Replaced oil drain plug washer with

OEM Oil Drain Plug Washer Gaskets For Mazda Part# 9956-41-400 (amazon)
(seems identical as OEM)
05-19-2019 03:45 PM
frosty I needed to use a torx socket (T50) to remove the drain plug...is everyone else's drain plug a torx or hex?
01-31-2019 03:44 PM
jchasp59 Thanks for your DIY oil change post. Things have changed a bit for the 2019 model. It uses a standard 17mm drain plug bolt rather than the 8mm plug on previous models. Otherwise, all is the same. An easy job!
05-22-2018 12:06 PM
Frishkorn
Quote:
Originally Posted by joelg1988 View Post
Quote:
Originally Posted by Frishkorn View Post
You didn't happen to notice a nice front jacking point did you? There is a jack adapter in the trunk, and I can see where it goes in the rear end. But I need to change my rotors and pads and would like to jack from the front rather than by the pinch weld / frame rails.
I agree with you about lifting vehicle from the front end tackling both rotors at the same time without having to jack each side separately, however I'd recommend you being careful about lifting a FWD vehicle from the front end, because even with the parking brake and the transmission in park (or in gear if you cave a manual). The car can roll back easily specially if you lift it at a high angle. (I used to work at a shop and I've seen this happen before.

When you have a RWD vehicle and you put the parking brake and the vehicle in Park, its almost impossible that it will roll if you lift the front.

My suggestion to you is to jack each side as you go (I know it's more work and it takes longer, but it's a lot safer).

just my 2 cents.
Agreed, I always use chocks since my FR-S I lift from the rear time to time for brake changes (track / auto x) and it being a manual RWD there’s nothing but the chocks to stop the front from rolling. I’ve just never liking lifting a car from one side and avoid it at all costs.
05-21-2018 04:54 PM
joelg1988
Quote:
Originally Posted by Frishkorn View Post
You didn't happen to notice a nice front jacking point did you? There is a jack adapter in the trunk, and I can see where it goes in the rear end. But I need to change my rotors and pads and would like to jack from the front rather than by the pinch weld / frame rails.
I agree with you about lifting vehicle from the front end tackling both rotors at the same time without having to jack each side separately, however I'd recommend you being careful about lifting a FWD vehicle from the front end, because even with the parking brake and the transmission in park (or in gear if you cave a manual). The car can roll back easily specially if you lift it at a high angle. (I used to work at a shop and I've seen this happen before.

When you have a RWD vehicle and you put the parking brake and the vehicle in Park, its almost impossible that it will roll if you lift the front.

My suggestion to you is to jack each side as you go (I know it's more work and it takes longer, but it's a lot safer).

just my 2 cents.
05-21-2018 04:16 PM
Frishkorn You didn't happen to notice a nice front jacking point did you? There is a jack adapter in the trunk, and I can see where it goes in the rear end. But I need to change my rotors and pads and would like to jack from the front rather than by the pinch weld / frame rails.
05-20-2018 08:27 PM
guitarman I see the owner's manual recommends oil changes at 7500 miles. I know that Toyota has been recommending 10,000 miles on their other models using synthetic oil. I also have a Toyota Camry, and that is their recommendation. So since this our iA models are really a Mazda should it be 7500 or 10,000 miles? Maybe I should ask the Toyota / Scion dealership.
02-16-2018 08:34 PM
joeb [quote=dantheman;47753]So just performed my first DIY oil change on Little Blue. It was very easy! I only needed a jack, a philips screw driver, oil catch pan, and an 8mm hex key (oil and oil filter too, ofcourse!)
First I jacked the passenger side of the car up. I used the screw driver to remove the little trap door on the engine splash shield to gain access to the oil filter and oil pan drain plug. Next, I positioned the oil catch pan and removed old filter with my hand (there was plenty of room to get my hand up and around it) Then I removed the drain plug with the hex key.
To finish I slapped on a new filter, replaced drain plug and filled her back up with 4.4 quarts premium synthetic oil.
Thought I'd post some pics for reference

How's the car been? reliable? I am getting quotes now from local dealers...I may be getting one in the Spring. In a manual transmission. I like the car and it seems trouble free.
01-19-2018 12:00 PM
patchleishman
Quote:
Originally Posted by dantheman View Post
For my first oil change I used a Mobil 1 Extended Performance M1-108A.
I used Royal Purple Extended Life filter 10-2876 for the most recent oil change.
How many miles are you doing your oil changes? 7500?
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome