Topic Review (Newest First) |
08-23-2019 02:12 AM | |
yrwei52 |
Oil change DIY Yes, I have. The first oil change was done by Toyota dealer covered by Toyota's 2-year maintenance program. 2.5 quarts of oil leaked out during the road trip from San Jose to LA! Brought back to the Toyota dealer afterwards the dealer claimed the drain plug aluminum washer is "cracked" and the oil is leaking out from there! |
06-20-2019 08:49 PM | |
WilsonT123 |
Anyone have issues with oil drain plug leaking.. Replaced oil drain plug washer with OEM Oil Drain Plug Washer Gaskets For Mazda Part# 9956-41-400 (amazon) (seems identical as OEM) |
05-19-2019 04:45 PM | |
frosty | I needed to use a torx socket (T50) to remove the drain plug...is everyone else's drain plug a torx or hex? |
01-31-2019 04:44 PM | |
jchasp59 | Thanks for your DIY oil change post. Things have changed a bit for the 2019 model. It uses a standard 17mm drain plug bolt rather than the 8mm plug on previous models. Otherwise, all is the same. An easy job! |
05-22-2018 01:06 PM | |
Frishkorn |
Quote:
Quote:
You didn't happen to notice a nice front jacking point did you? There is a jack adapter in the trunk, and I can see where it goes in the rear end. But I need to change my rotors and pads and would like to jack from the front rather than by the pinch weld / frame rails.
When you have a RWD vehicle and you put the parking brake and the vehicle in Park, its almost impossible that it will roll if you lift the front. My suggestion to you is to jack each side as you go (I know it's more work and it takes longer, but it's a lot safer). just my 2 cents. |
05-21-2018 05:54 PM | |
joelg1988 |
Quote:
You didn't happen to notice a nice front jacking point did you? There is a jack adapter in the trunk, and I can see where it goes in the rear end. But I need to change my rotors and pads and would like to jack from the front rather than by the pinch weld / frame rails.
When you have a RWD vehicle and you put the parking brake and the vehicle in Park, its almost impossible that it will roll if you lift the front. My suggestion to you is to jack each side as you go (I know it's more work and it takes longer, but it's a lot safer). just my 2 cents. |
05-21-2018 05:16 PM | |
Frishkorn | You didn't happen to notice a nice front jacking point did you? There is a jack adapter in the trunk, and I can see where it goes in the rear end. But I need to change my rotors and pads and would like to jack from the front rather than by the pinch weld / frame rails. |
05-20-2018 09:27 PM | |
guitarman | I see the owner's manual recommends oil changes at 7500 miles. I know that Toyota has been recommending 10,000 miles on their other models using synthetic oil. I also have a Toyota Camry, and that is their recommendation. So since this our iA models are really a Mazda should it be 7500 or 10,000 miles? Maybe I should ask the Toyota / Scion dealership. |
02-16-2018 09:34 PM | |
joeb |
[quote=dantheman;47753]So just performed my first DIY oil change on Little Blue. It was very easy! I only needed a jack, a philips screw driver, oil catch pan, and an 8mm hex key (oil and oil filter too, ofcourse!) First I jacked the passenger side of the car up. I used the screw driver to remove the little trap door on the engine splash shield to gain access to the oil filter and oil pan drain plug. Next, I positioned the oil catch pan and removed old filter with my hand (there was plenty of room to get my hand up and around it) Then I removed the drain plug with the hex key. To finish I slapped on a new filter, replaced drain plug and filled her back up with 4.4 quarts premium synthetic oil. Thought I'd post some pics for reference How's the car been? reliable? I am getting quotes now from local dealers...I may be getting one in the Spring. In a manual transmission. I like the car and it seems trouble free. |
01-19-2018 01:00 PM | |
patchleishman | How many miles are you doing your oil changes? 7500? |
This thread has more than 10 replies. Click here to review the whole thread. |
Posting Rules | |